АВТОЗАГАР

Корзина

В вашей корзине:
0 товар(ов).

Сумма заказа:
0.00 грн.


Голосование

Версия для печати Версия для печати

MEGASUN ERROR CODES коды ошибок

Оценить

megasun 6800  7900  и другие горизонтальные солярии

 

E01BUS:ABL There is not any data link between the controller board and the revolution control... Reason: defective or not connected I²C revolution control.

 

E02:BUS:TMP Reason: defective or not connected I²C temperature sensor. Solution: press the START key. The blower is running with max. revolution during the temperature controll.

 

E04:BUS:VOIC Reason: There is not any data link between the controller board and the MP3 player Voice. Solution: press the START key. The controller is working as one w/o megaVoice. Reason: — missing soldering bridge on MP3-Player megaVoice, — SD card not readable — formating or wrong inserted, — Plug at MP3 iInterface or at I²C Audio switch is inserted uncorrect.

 

 

E05BUS:REL Conguration error: I²C-Relay board (8) an I²C Relais board (2) at the same time connected.

 

 

BUS-Error Daten line of the Bus I²C-Bus is disturbed — 230 V is missing at MP3-Player or Audio Switch — Bus connector at MP3-Player in wrong position

 

 

Error message “Ende der Besonnung“ „End of tanning session“ This message will be displayed after 40 minutes of uninterrupted operation of the tanning system. By turning off the coin-operated system this message is acknowledged.

 

 

 

Error message “Abluft“ oder “Windschalter“ This error messageis displayed on the operating panel and can be acknowledged by pressing the “Stop“ key. Prior to this, service staff has to nd the reasons of these error messages. Possible reasons can be: • temperature in the unit is too high • exhaust vent system is defectiv

 

 

 

MegaSun Pure Energy вертикальные солярии

Faults nos. 07, 08, 12 and 13 do not occur with the KBL/5 processor due to its equipment and processor structure.

 

Temp. Err    Exhaust air, Excess temperature bimetal!     

 

max. time    Incoming enabling signal from coin-box system longer than approved, i.e. the value specified under “Maximum tanning time” (voltage remains connected).

 

> 66 °C   The sensor has measured the limit value of 66 °C.

 

> 62 °C   A temperature exceeding 62 °C is measured for more than 3 minutes.

 

1 sensor f    One temperature sensor has not been found by the control system.

 

2 sensor f    Both temperature sensors have not been found by the control system. Ventilation works at 100 % power.

 

Aqua low     The content of the aquaCool canister is sufficient for another 750 spraying seconds (2.5 operating hours at a cycle time = 1 minute).

 

Bus Error    I²C bus faulty.

 

measur. f    Temperature values outside the range of 0 - 85 °C.

 

1-Wire f    No connection to 1-wire-adaptor (e.g. cable break). Bus cable or 1-wire bus adaptor defective.

 

Aqua 0%    750 spraying seconds (2.5 operating hours at a cycle time = 1 minute) have expired.

 

Hardware error    Main board defective

 

 

 

 

Есть вопросы?

Вы можете задать нам вопрос(ы) с помощью следующей формы.

Имя:

Email

Пожалуйста, сформулируйте Ваши вопросы относительно MEGASUN ERROR CODES коды ошибок:


Введите число, изображенное на рисунке
code